![]() |
|
|||||||
| Register | FAQ | Members List | Calendar | Search | Today's Posts | Mark Forums Read | |
| TireRack Garage | Homepage | Supporting Vendors | Articles | Online Store | Photo Gallery | Forum Rules | Advertising |
| Forced Induction sponsored by Active Autowerke Discuss turbocharging and supercharging your BMW engine. Also force-feeding Nitrous, Propane or water. |
![]() |
|
|
Thread Tools |
|
#1
|
||||
|
||||
|
E46 M3 chassis Drag car with 4 Rotor twin turbo (8.22 1/4mile)
__________________
![]() |
|
#2
|
|||
|
|||
|
i didnt know they made a 4 rotor motor...crazy stuff
__________________
CP Pistons
Eagle Rods T67 Turbo Lots and lots of custom goodies and 666 fab schtuuufff 05/01/07 RIP pops |
|
#3
|
|||
|
|||
|
They never mass produced a 4-rotor engine. But with the way a rotary is, it's not hard to "stack" it and make a 4-rotor. I've seen ones stacked to 6-rotors.
__________________
![]()
|
|
#4
|
||||
|
||||
|
Crazy down under guys!
__________________
![]() My BBS RC's are for SALE Do not argue with idiots...they only drag you down to their level and beat you with experience. |
|
#6
|
||||
|
||||
|
E46 M3 body maybe, but certainly not the chassis.
That thing is crazy! I'm curious as to what it would run fully setup.
__________________
![]() '97 M3 - Techno/Black - VF SC - Technique Tuning - Bilstein PSS9 - SSR - ZKW/HID |
|
#14
|
||||
|
||||
|
I think it's been stated before that it's nowhere near a BMW besides the look of the outer shell. No BMW engine, no BMW transmission, no BMW suspension, frame probably isn't even BMW.
__________________
A word of Internet Forum wisdom: Disregard any advice that begins with "I've heard..."
StreuBocharged 97 M3/4 - Top Mount Turbo Kit, Built/Stroked M50 Non-Vanos, GT-35R, Aquamist HFS-5, 3" Turbo Back Exhaust, HR/Bilstein Combo, UUC SSK/Sways/LTW Flywheel, AA DSB 93 532i Touring - S52, GT35r, NickG Tune, Manual Swap, Custom Intake Mani by got_psi Buy some domains! shortshifter.net, .org and .info. PM me for details. |
|
#15
|
||||
|
||||
|
What are those 4 things on top of the tranny?
__________________
![]() You know you love rock climbing: Walltopia USA Widebody Turbo Build "A realist in a world of dreamers" |
|
#16
|
||||
|
||||
|
Rofl, rotories (especially 20B's and custom quads) sounds like they are trying to self destruct with any kind of decent port on them.
__________________
|
|
#21
|
||||
|
||||
|
It's a Lenco manual transmission with air shifters.
http://www.lencoracing.com/CS1MasterPage.html http://www.lencoracing.com/LENCOShiftersPage.html
__________________
.-=[ Kenny ]=-.
1999 BMW M Coupe 10.775 @ 134.35 mph w/1.600 60' (Best 136.07 mph) - pass made 25th August 2004. See the BFc Drag Racing Standings List for BMW street cars. Watch my drag racing movies on YouTube. BMW turbo street car Drag Racing 101 Drag racing 101 part 2 Best rubber fitment for BMW street cars with unmodified bodywork Drag Racing 102: Advanced techniques What fuel is what? Gearing for drag racing 101 NHRA rule book for street cars
Last edited by MrBlonde; 07-23-2007 at 06:01 AM.. |
|
#22
|
|||
|
|||
|
I like it, though they woulda been better off with an RX7 body. It's smaller, lighter, and its a mazda so the rotary actually belongs in there. Then again its cool to make something special and original.
|
|
#23
|
||||
|
||||
|
the BMW bodyshell actually fits all that crap in there, unlike the RX7 shell. a few of the quick aussie blokes have the wheel tubs sticking out of the rear hatch.
Sure, there is prolly less frontal area with a RX7, but the bimmer shell is just so cool ![]()
__________________
Fast, Cheap, Reliable - Pick any two, and the third is laughable
|
|
#25
|
|||
|
|||
|
ok we gotta stop talking about australia! i just got back from living there for 6 months and i am getting really nostalgic right about now!!!
![]()
__________________
![]() TCD S3 Completed! 400 rwhp/455 tq. Tuned by Larry Strouth @ HP Works. www.Turbochargingdynamics.com http://forums.bimmerforums.com/forum...929post7215929 <-------Parts for sale |
![]() |
| Bookmarks |
| Thread Tools | |
|
|