Just had the car aligned, and went over it with a fine tooth comb it is truly ready to race!
price is FIRM, $20,500 and has been lowered to rock bottom price
Last Run at VIR Full with a time of 2:14

Drivertrain
Car has 101,000 miles on the chassis
Newly rebuilt motor 3.0L, leveled head, polished cam/crank journals,
balanced, full head rebuild, all seals, valves, lifters, retainers are new
All work was done within IP Spec's by “Cylinder Head Specialties” in Wake Forest.
new timing tensioners
Schrick Race Cams
Secured/welded oil pump nut, new oil pump
Active Autowerks Cloned Headers,
full custom 3” catback exhaust(no cats)
Ireland engineering Poly Engine mounts
Typical add ons for cams, AA chip, HFM, AA intake, 24# injectors
Brand new Clutchmaster sprung hub clutch
Metrix performance built 3.64 LSD 30% lock rear Diff
UUC EVO short throw shifter
UUC Power Pulley set, including alternator lightweight pulley(not under driven just lighter)
Recently Replaced the transmission recently with low miles replacement
shifter bushings, All seals and shift pins were replaced.
AA Transmission bushings with reinforcing cups
AA rear Diff Support Bracket
New Driveshaft Guibo
Bimmerworld Dual Fuel pump kit
New fuel filter and metal filter cover
New radiator and metal thermostat cover
Less than 2000 miles on water pump

Entire suspension is top of the line Ground Control, except rear camber arms
Ground Control front race camber plates
Ground Control Advanced Design Coilover DAShocks , fresh rebuilt less than 10 days of track time on shocks
Ground Control LCABearings
All bearings in shocks were replaced
Ground Control Rear Upper race shock mounts
SPC rear camber Arms
Brand new LCA's 3 track days on new arms. Meyle control arms with Solid metal joints
new rear subframe bushings, Poly kit from Bimmerworld
Ground Control Articulating rear weight jacks
Eibach 800lb front springs and 950lb rears
Lower Xbrace
Aluminum Upper Strut bar
UUC sway barbarians sways
New trailing arm bushings with the delrin spacers
New Poly Subframe bushings and subframe reinforcements
lug bolts all replaced with studs
New CV axles on one side and CV boots on the other side
New Diff bushings
Fresh alignment for the season 0 days on alignment
Full custom 6 point cage with Nascar drivers bar and Window net
Set of 5- 17x8.5 Kosei's with RA1's 2 track days on these tires

Aero
ExtremeSpeed Front splitter w/splitter supports, goes from 2" past front bumper to front axle
Custom Dive plates
Vortex generators on rear roof line
APR GTC200 Spoiler with custom machined spoiler stands.

Misc
Battery box
Dry weight @ 2780lbs (low enough to put me right at the legal weight
Typical gauge set, oil press, water temp and oil temp.
SPAL electric pusher fan with auto thermostat
Momo Quick release steering wheel hub and Race flat bottom steering wheel
Stainless braided brake lines
Stainless braided clutch line
brand new clutch slave cylinder
Turner Motorsports head light FRP Intake
Lightweight race battery
6 panel Wink mirror
Maintained heater core and heat system
Prewired for AMB system
New serpentine belt



This is a “short” list off the top of my head
I have built this car from the ground up, replaced every bushing and have not skimped on build quality 110% turnkey racecar.
The car is fast, quick and easy to drive!!!

Here are a few pics, more upon request....

http://www.extremespeedonline.com/gallery2/main.php?g2_view=core.DownloadItem&g2_itemId=89057&g2_serialNumber=6

http://www.extremespeedonline.com/gallery2/main.php?g2_view=core.DownloadItem&g2_itemId=90957&g2_serialNumber=1&g2_GALLERYSID=1d61f8864fe8ecee81920eb3b6847b48

http://www.extremespeedonline.com/gallery2/main.php?g2_view=core.DownloadItem&g2_itemId=90943&g2_serialNumber=2&g2_GALLERYSID=1d61f8864fe8ecee81920eb3b6847b48

http://www.extremespeedonline.com/gallery2/main.php?g2_view=core.DownloadItem&g2_itemId=90933&g2_serialNumber=1&g2_GALLERYSID=1d61f8864fe8ecee81920eb3b6847b48


http://www.extremespeedonline.com/gallery2/main.php?g2_view=core.DownloadItem&g2_itemId=9306&g2_serialNumber=6&g2_GALLERYSID=1d61f8864fe8ecee81920eb3b6847b48

this car is awesome, what are you selling for? Hopefully staying in racing...

yeah staying in racing, just moving up to something with more power/V8

car has been totally sorted out, literally every weak point in an e36 has been addressed. Clean title, no accidents.

Bump for a great car and a good guy. Hate to see it go Eric but I know the next one will be sick!

Those headlight cutouts legal in prepared?

Good Luck with your sale...and a good seller!

Nice car. GL with the sale!

Those headlight cutouts legal in prepared?

Good Luck with your sale...and a good seller!


Not really, the passenger side light is just painted black, and I have the drivers side light to throw back in, I just put those in for HPDE's.........it looks cool :-D

Bump for a fast car! This was one of the only cars to pass me at Wilderness Trail HPDE March 18th at VIR!
Kevin
not stock Estoril E36 M3

Looks like a good car, how competitive is it in class?

I've heard different things re: the 3.0's vs 3.2's.

Thanks

Looks like a good car, how competitive is it in class?

I've heard different things re: the 3.0's vs 3.2's.

Thanks

I'd say its a solid mid to mid front pack car. It is by no means a front runner like David Whites car, but should run solid 2:09-2:11s with a good driver and some hoosiers. For a front runner like David White's you'd probably spend another 15-20k at least. hell he probably has that in just motorworks.

I ran low 1:23's at Roebling, 2:14's all day at VIR, with better tires and driver It has much more in it. I'm just not pushing it 100% and beyond.

BTW, car will be at VIR this weekend for the THSCC event if anyone wants to see it and if anyone is serious, they can drive it.

Will you be racing at the club race at VIR? I'll be there might sneak a look.

For a front runner like David White's you'd probably spend another 15-20k at least. hell he probably has that in just motorworks.

not even close...probably not much more than you have in your motor...junkyard 3.2, sunbelt cams, injectors, intake, supersprint headers, tuning...also have an oil cooler and dual sump oil pan but those don't add power...

my 3.2 makes good power but not big power like some tend to think...what makes an IP car fast is a good suspension that is properly dialed in, not so much horsepower...

not even close...probably not much more than you have in your motor...junkyard 3.2, sunbelt cams, injectors, intake, supersprint headers, tuning...also have an oil cooler and dual sump oil pan but those don't add power...

my 3.2 makes good power but not big power like some tend to think...what makes an IP car fast is a good suspension that is properly dialed in, not so much horsepower...

I stand corrected :( I had heard you had the motor built pretty stout and had just about everything that can be done legally done to it. Sorry about the misinformation.

what makes your car fast too, is the fact you drive the friggin wheels off it! ;-)

left out one thing, we had the head refreshed on the junkyard motor (no tricky parts though)...motor is strong, but actually not much more power than my 3.0 made (another stock motor with sunbelts in it)...imho, there's no need to dump a bunch of money into a motor rebuild since you can't really do anything (legally) in prepared other than cams/injectors/intake/exhaust...

good luck with the sale...the way IP seems to be growing right now, you should be able to sell it fairly quickly...

left out one thing, we had the head refreshed on the junkyard motor (no tricky parts though)...motor is strong, but actually not much more power than my 3.0 made (another stock motor with sunbelts in it)...imho, there's no need to dump a bunch of money into a motor rebuild since you can't really do anything (legally) in prepared other than cams/injectors/intake/exhaust...

good luck with the sale...the way IP seems to be growing right now, you should be able to sell it fairly quickly...

Thanks, I hope so, I have a lead on a solid Panoz GT-WC car! Are you going to be at VIR this weekend with THSCC?

Are you going to be at VIR this weekend with THSCC?
that's the plan...

You said you addressed all the problems with the e36 -- I just got a 95 m3 and it seems to push pretty bad, did you have a similar problem ? If so how did you fix it.

Thanks!

You said you addressed all the problems with the e36 -- I just got a 95 m3 and it seems to push pretty bad, did you have a similar problem ? If so how did you fix it.

Thanks!

non staggered wheels, sticky tires, loads of suspension tweaks, stiffer springs, stiffer sways. A little trail braking and throttle steer helps too! :-D

Come on, noone wants a solid IP car? car is ready to drive on track, fresh fluids!

The e36 track market just doesn't have a ton buyers in it right now. But there is someone out there who wants this car and is willing to pay your price, which seems fair for the car. It might take some time, but you'll get it sold (coming from someone who just sold my other e36 m3 track car). Is it on all the sites possible? CCACR, roadfly, turner, bimmerfest? Mine ended up selling by word of mouth, so the more places it's listed the better.

I bought mine by word of mouth also, so defeintly post it as many places as possible.

Thanks for the understeer tips :).

Good luck with the sale! Thats a sweet car.

Bump for a great seller and a fast car.

The e36 track market just doesn't have a ton buyers in it right now. But there is someone out there who wants this car and is willing to pay your price, which seems fair for the car. It might take some time, but you'll get it sold (coming from someone who just sold my other e36 m3 track car). Is it on all the sites possible? CCACR, roadfly, turner, bimmerfest? Mine ended up selling by word of mouth, so the more places it's listed the better.Yup.....my former IP took over a year to sell. I had it on all the boards too. Be patient. I am in the market for another IP car but your is more than I want to spend right now. GL :)

Price reduced, but its as low as I am going for now. $23,900

looking to sell the trailer seperate?

looking to sell the trailer seperate?

No, sorry, I don't really want to sell the trailer at all, but if it would help sell the car I would, otherwise I'll keep it.

looking to sell the trailer seperate?

He'll sell the trailer for $24,500


:devillook


:stickoutt Bump for a good car

Bump

bump

Still available Eric?

Thanks

John Corbs

yup

bump

you didn't have this one long did you? I thought I remember the for sale thread when you bought it and started building it.


Good luck with the sale regardless! And I'd love to check out the Panoz if you get it.

I had it 2+ years, I'm a project guy, when the projects done, i get bored, did the same thing with my 350z, then the Viper, then the M, and now onto a new project. never kept a track car more than 2 years.

Thanks for the bump. I found the Panoz I want, now to sell this one!

Eric,

Mike from Wilkesboro here, if you get a chance to send info, I will try to
give you an answer ASAP. Thanks, mk

email me at: mike@esignz.com

bumpity bump

bump

bump...

Lowered price, Car is going to alignment shop to get a fresh alignment for the season.

Will sell the car for $22k without extra Rims and spares. The car is 110% ready to drive on track!

For anyone who cares, I just had a full inspection done on the car by a local race shop www.apexvintage.com (http://www.apexvintage.com) With the exception of a few little nitpicky things the car checked out great.

One of the things they noticed was the power steering lines were leaking so I replaced those tonight. Car is ready to sell!

Bump for a good deal.

anyone anyone? Price lowered to $21,500 firm Priced to sell. Solid race/track ready

turn key car, come on! :-D

Devin and I have our cars picked out so its time to sell!

Threw the car up on ebay, a few bidders and lookers, doubt it will sell there but god to advertise right?
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&viewitem=&item=220234606510

Some video of the car from this past weekend. Took it easy on the car because its up for sale, but a FUN weekend.

http://www.youtube.com/watch?v=nwe9FP1_eQI

BUMP for a great car at a killer price.... I bought one a few months back and I paid a good deal more then this.... Try and build a car for this price...

Someone buy this thing.....

Cool Vid too.....

Come on....somebody buy this thing so that someone other than Eric can continually pass me in it.

It is one hell of a car at that price.

Some traqmate data to show the performance of the car, I know its not a HUGE indicator but gives you an idea

http://www.extremespeedonline.com/gallery2/main.php?g2_view=core.DownloadItem&g2_itemId=91760&g2_serialNumber=1

21 Firefox tabs?!?!?!?!?!

Come on, man.

Man, this is so tempting Eric, just so I can pass Sean, then again this car might not be enough for that with my lackluster driving skills...

Alex.

Man, this is so tempting Eric, just so I can pass Sean, then again this car might not be enough for that with my lackluster driving skills...

Alex.

Come on, buy it already! ANYONE can pass sean in it, I mean, I never took mine out of 3rd gear and i was faster than him ;-)

I hope you are never able to sell that thing.

:(

I hope you are never able to sell that thing.

:(

BUt then youd have to stare at my taillights for years to come :-D JK:redspot

Eric,

So what's the policy on test drives? Are you at Tarheel next week?

Eric,

So what's the policy on test drives? Are you at Tarheel next week?

Normally i wouldn't mind, but I'm not going to bring my car next week, at least i hadn't planned too.

If youre reallyserious about it I can haul it up there, but I don't want to press my luck and drive it and have something happen to it(wreck it)

$20,000 even anyone

You must be getting a lot of interest - your pm is full!

cleared sorry

updated the list of parts, chock full o' goodness

bump

price reduced $20,000obo

sell... sell.... buy....buy....

bump, make me an offer!

Eric, You may want to think about parting out your car instead of selling it whole. I'll bet you'll make more money that way too - it's just a PITA though. - Denis

Denis, i thought about it, but it is entirely to much work, i did the math and I could easily get quite a bit more out of it by parting it out, but it would defeat the purpose of all the work I've done over the past 2 years and take way too much time, that with a new baby on the way I do not have. Thanks for the input though.

bump

bump, still for sale

Bump for a good car and a good seller.

for a total price of $20k I'll throw in a 16' trailer with tire rack

for a total price of $20k I'll throw in a 16' trailer with tire rack

:eek:

Come on, someone buy it already!

Man, I would've seriously consider buying your car (selling both of my E30 and E36 M3s) if I didn't have a child on the way.

Maybe you want to do a trade? :)

Good luck on the sale.

Come on, someone buy it already!

Man, I would've seriously consider buying your car (selling both of my E30 and E36 M3s) if I didn't have a child on the way.

Maybe you want to do a trade? :)

Good luck on the sale.

e30 plus cash? lol

e30 plus cash? lol


Let's talk.

Check your PM.

Peter

I know this will put any potential buyer over the top but I also just installed a set of UUC power pullies. Now everyone stand back and start the bidding war!

:-D

bump

Do you car sell ??

Do you car sell ??

Yeah his car sold, but contact me if your still looking for one. :buttrock