Just looking to see how many people in the area have been waiting or wanting there fenders rolled but haven't had the time or money. I know I have. I spoke with Josh (The owner of Euro Technologies) and he said he would be down to do a fender rollin' GTG. If you want all corners or just the rear, or whatever he'll do it but only if there's a reasonbale number of people. The shop is located in Lynnwood near 148th for those of you who may not know. Just post up if you're interested and I'll give him a status report on the number so we can set-up a good time and date .....and the amount of people interested will determine the price per-corner. He also does a badass job of tinting. He'll basically do what ever you want. None of this it's gotta be legal crap!:buttrock

i do but i dont want to drive to WA. Anyone in OR know how to do this? i plan on some 9.5's in the near future.

im down. wana fit some 255's in the rear

I might be down... getting coils on and now Ill need spacers on fenders rolled for my 9.5 rears

The only thing puting fatter tires will do is make you understeer more and help you slightly with launching, but that's all technique anyways.

Go with 245's all the way around and call it good. Sure rolling the fenders enables you to have a bigger lip, but it that just means more wait in a place that really matters.

To those of you who did power pullies and noticed a difference. You obviously understand or at least acknowledge that more rotational mass = bad for these cars. It's no different with your driveline, except you're dealing with substantially more weight, not only while sitting, but when you're moving, that extra weight is multiplied.

i would be interested depending on the price and how many people we can get.

how soon... i need new tint put on .. and my front pass side re rolled it scrapes just a lil on a locked turn
how much to tent m3 coupe anyone know ... im prolly going to end up going to midnight tinting because they have that special of 130 going on ... and i have only heard great things

I'd be interested.

I'd be down...but I wont be bringing the bimmer home when I come home on the 14th. Bummer, I wish the guys in Florida did stuff like this.

I'd be down...but I wont be bringing the bimmer home when I come home on the 14th. Bummer, I wish the guys in Florida did stuff like this.


i havent seen you around in from OH too ... wanna meet up some time?

Okay, so a few so far...sweet, I'm sure they're are more out there. It doesn't have to be just BMW's if you guys have buddies that want/need it done also. He just prefers to work on Euros now days. I also had asked him about a tint job on the coupe and he said it depends on what % it's at and how you want the edges (bevelled or straight) He quoted me the avg. of 220-240 (with bevelled edges). But I watched him do a full Passat and it looked tits when he got done. He did a badass job. I know it's a little pricy....how long is Midnight's special going for. If I can get it for $130 or whatever, I'd rather do that if they do just as good of a job.
The time will be predicated on how many of us will be available around the same time. Most likely a Sat. early afternoon or something. We can figure that out later. I'm gonna talk to him this weekend and find out some more info for everyone and I'll let you know. I know he was ordering a new fender tool from Snap-on so I'm not sure how long it'll take to be dropped off. So I'll keep you guys posted! Thanks for the replys-

:redspot

I'm interested. Do you have a ballpark figure on price?

It depends on if you want all four or just the rears. He knows the avg price is usually between 40-70 bucks a corner...so depending on what everyone is wanting.....and it seems that it's probably going to be rears, I was going to ask for something like 80-100 for the deal. And see what he comes back with. He's pretty cool and understanding so I know he'll give everyone a good deal. He's a perfectionist too so I can guarantee a great job!

I just stumbled on to this site and I just happen to need my rears rolled. Ive been looking every where in the Seattle area with no luck. I would be in for sure.

I'm interested in this deal also.

It'll be nice to not have to worry with rubbing once i get my new suspension setup on. :)

Okay, so a few so far...sweet, I'm sure they're are more out there. It doesn't have to be just BMW's if you guys have buddies that want/need it done also. He just prefers to work on Euros now days. I also had asked him about a tint job on the coupe and he said it depends on what % it's at and how you want the edges (bevelled or straight) He quoted me the avg. of 220-240 (with bevelled edges). But I watched him do a full Passat and it looked tits when he got done. He did a badass job. I know it's a little pricy....how long is Midnight's special going for. If I can get it for $130 or whatever, I'd rather do that if they do just as good of a job.
The time will be predicated on how many of us will be available around the same time. Most likely a Sat. early afternoon or something. We can figure that out later. I'm gonna talk to him this weekend and find out some more info for everyone and I'll let you know. I know he was ordering a new fender tool from Snap-on so I'm not sure how long it'll take to be dropped off. So I'll keep you guys posted! Thanks for the replys-

:redspot

i just called midnight window tinting everett (its closer to me) and he said he could do a 95 m3 coupe for $150 any standard color tint (5% and up) i scheduled an appointment for tomorrow night ill let you guys know how it comes out :) finally no more peeling back window tint :)

I wish he would drop his tint price. 1bad m3, please post a thread on your tint when you get it back.

oh dude, they're in Everett! That's hella close to me. Yea man let me know how that goes and I'll go there. $150, can't go wrong with that!-Good work-:D

I'm interested in this deal also.

It'll be nice to not have to worry with rubbing once i get my new suspension setup on. :)


Yea I was thinking the same thing, I just got mine in the mail two days ago and I want to get this done before I slap it on there.

well ill let everyone know how it goes ... :shifty

What kind of tint film do they use, 1bad m3?

I'm down.

What kind of tint film do they use, 1bad m3?


i just called he said johnson and filmtec mainly but they do use others...

2yr warrenty on the standard film from fadding lifetime for bubbling peeling ect ect

lifetime everything on the premium film

ill prolly end up getting the premium tomorrow i asked he said its an extra 49.95 to get premium .... so that will put it around 210 out the door... im going to try and talk him down tomorrow.

I was afraid of that. I've had the non premium type film before, and it just turns purple.

I was afraid of that. I've had the non premium type film before, and it just turns purple.


word ... well i still let everyone know how it goes :)

Is johnson a premium film, does anybody know?

i'm in for sure! i've been waiting for this for EVAR. i can't make any camber adjustments till i roll the fenders :(

i'm in for sure! i've been waiting for this for EVAR. i can't make any camber adjustments till i roll the fenders :(

Nice! You're rollin' 19's right? What size tires do you have?

i'm in for sure! i've been waiting for this for EVAR. i can't make any camber adjustments till i roll the fenders :(

So you are keeping the race springs?


Nice! You're rollin' 19's right? What size tires do you have?

No, they are 18s.

i'd be interested but only after i install my coilovers (any week now...)
i need to see whether i'll have any rubbing.

i'd be interested but only after i install my coilovers (any week now...)
i need to see whether i'll have any rubbing.


I'll be installing mine soon also. But I was curious for the others running c/o if it's completely neccessary to use camber/caster plates in the front and the adjustable control arms in the rear in order to get a close enough alignment as to not eat away at the tires too fast. Anyone know if this can most likely be delayed without spending tons of money on just replacing tires?

Hopefully you guys get the idea behind the question...Thanks for any help!

Nice! You're rollin' 19's right? What size tires do you have?
well you can adjust your stock components to an extent so it depends on how much of an adjustment you need. i need a little over 1 degree adjustment all around so i'm getting camber plates/adjustable control arms.

and no i have 18"x8.5"s et38 with 225/40s. the h&r race gave me -3degrees camber in the back and -2 in the front. but i may be pulling out of doing this fender rolling, i found a local shop that will do it for $100 an axle

^^ Bummer, that's alright it would be a little bit of a drive for you. It's pretty good price too.

What's the negative doing to you rubber or have you not had it set-up long enough to tell the difference in wear?

^^ Bummer, that's alright it would be a little bit of a drive for you. It's pretty good price too.

What's the negative doing to you rubber or have you not had it set-up long enough to tell the difference in wear?
hah, it's tearing the shit outa my rubber just one the inside edge. but then now i can just rotate the tires and wear out the other side till i get the camber kit on. good luck!

Any word yet when the fender rolling going to happen?

^^ I'm gonna swing by a talk to Josh in person today for some more details. And I'll post up what I find out. Lets take a head count so I can let him know how many people are still interested so I can quote you guys the right price...


1. Veedubbvr6 (Jon)
2. cstaley
3.
4.
5.
6.
7.
8.
9.
10.

Im in for sure. Im scrapping bad.

1. Veedubbvr6 (Jon)
2. cstaley
3.1bad m3 (joseph)
4.
5.
6.
7.
8.
9.
10.

Im definately in as long as its not too expensive. I recently put 19s on my car and i rub every time i go in and out of my driveway so im looking forward to this


1. Veedubbvr6 (Jon)
2. cstaley
3.1bad m3 (joseph)
4. Tucked M3
5.
6.
7.
8.
9.
10.
<!-- / message --><!-- sig -->

Hey Tucked, what size tires/wheels do you have currently? Are you rubbing all 'round or just rear? Stock suspension or lowered? I'm only asking because I'll be getting some 19's soon and I'am waiting to put my coilovers on so I'm just curious what I'm in for. :stickoutt

And just another update on the rollin' day..I swung by his shop on Sat.,and he wasn't open:( ...called him today...no answer:( . I don't know WTF is going on, but when I know, you'll all know. If push comes to shove I'll try and find another place that can hopefully get us a good group deal. Someone a little more reliable than this guy. I don't wanna keep playing tag like this!:shifty

Thanks for the update. Keep us posted.

Hey Tucked, what size tires/wheels do you have currently? Are you rubbing all 'round or just rear? Stock suspension or lowered? I'm only asking because I'll be getting some 19's soon and I'am waiting to put my coilovers on so I'm just curious what I'm in for.

well i have 19x8s with 215/40 in the front and 235/40 in the rear. the rear is where i rub cuz im actually tucking rim. im plannin on getting coilovers this spring so i can keep it dumped at the shows then raise it up for when im racing or cruising around. keep me posted on whats happening because my homie has a bagged c320 who would also be interested

no problem, will do.....Hopefully I'll hear something soon.

any update?

any update?


Yea, no...:(
I don't think I'm going to use this guy anymore, he's obviously unreliable. I'd hate to actually speak to him and then agree on a day to do it when everyone shows up to realize he's not even there. I would just hate it to be a waste of time for everyone. At least the ways things are going at this point. Sorry guys..

Hey turbodefrost, did you ever go to the shop for $100 an axle? Did they do a good job? I wonder if they would do a discounted group thing. If you haven't done it yet, you should ask them. Or wait, it's in Bellingham huh?

Does anyone know of an other shop that rolls fenders?

I'll be getting the fender rolling machine in the next two weeks. If you guys want you can rent it from me (cheap) or have a get together at my place and do it there. (Renton)

I'd be down for either or. I guess if we could get some people together that would be better, but if not I'd rent it from you! Right on man, thanks for another work about.

I dont want to sound like a sissy but Im affraid I would screw my car up if I did it myself. Have anyone of you guys ever did this before?

Not I, but I figured I would try it on my GTi first and see what happens. If I don't feel confortable doing it myself on the bimmer, I know some of my mechanic friends would be willing to help me out with it. I know how you feel, I wouldn't want to screw it up either:D

Yea, no...:(
I don't think I'm going to use this guy anymore, he's obviously unreliable. I'd hate to actually speak to him and then agree on a day to do it when everyone shows up to realize he's not even there. I would just hate it to be a waste of time for everyone. At least the ways things are going at this point. Sorry guys..

Hey turbodefrost, did you ever go to the shop for $100 an axle? Did they do a good job? I wonder if they would do a discounted group thing. If you haven't done it yet, you should ask them. Or wait, it's in Bellingham huh?
I just got my fenders rolled saturday at a shop called 20/20 customs. They did a phenomenal job. AND it only cost me $25 a corner!! I'd recommend for anyone willing to make the drive to get yours done from these guys. They know what they're doing. Only problem is i'm still to low. Probly gonna get some coilovers so i can choose exactly the settings i want. Good luck everyone!

$25 a corner?!!? Wow, I'm gonna check 'em out. Just gives me a reason to take a nice drive. I like makin' way up there on nice days....I get my wheels on Thurs, so maybe I'll do it this weekend. Did you have to make an appointment or did you just show up? Do you happen to have their phone number?

Thanks for your update, I'm glad they did a good job for you!
:buttrock

I have done them for three different E36's easy job. It just takes time.

I just got my fenders rolled saturday at a shop called 20/20 customs.

Where is this?
Anyone know someplace near Portland/Salem that does a good job?

I dont get up to B Ham very often so I will continue my search down in the Seattle/Eastside area. If anyone knows how to do it and make some extra money let me know. All I need is my rears done.

I have done them for three different E36's easy job. It just takes time.

Did you get your tool yet? How'd it work out for ya?

uh i have there card somewhere i'll have to find it. They're a good shop. and if you need it they can stretch your fenders out a little too.

sweet! Did they tell you how much the stretching is? How long did it take them? Were you able to watch them do it?....rolling that is...

sweet! Did they tell you how much the stretching is? How long did it take them? Were you able to watch them do it?....rolling that is...
I don't think they'll really charge too much more for extra stretching. I didn't watch them do the rolling. I also had my adjustable control arms installed. but the actual rolling part only takes them an hour or so.

uh i have there card somewhere i'll have to find it. They're a good shop. and if you need it they can stretch your fenders out a little too.

Did you ever find thier number? I tried looking them up on 411.com and nothing came up in washington.... Thanks-

Did you ever find thier number? I tried looking them up on 411.com and nothing came up in washington.... Thanks-
oh yeah sorry i forgot to do that. I'll try to remember to get you the # when i get home from class today

20-20customs 360.543.7927 www.2020CUSTOMS.com