So what's the shop around here to goto for dyno AND tuning?

Possibly setup a dynoday? I need one done before the VIR event.

Dynojets do not make the best tuning tools. You want a load-bearing dyno like a Mustang or DynoDynamics. Ideally, you want to do a street tune but it isnt always feasible to do multiple 4th gear pulls around your neighborhood. :stickoutt

Dynojets do not make the best tuning tools. You want a load-bearing dyno like a Mustang or DynoDynamics. Ideally, you want to do a street tune but it isnt always feasible to do multiple 4th gear pulls around your neighborhood. :stickoutt

O.. ok, maybe no tuning then. Just dyno.. but it HAS to be Dynojet as required by NASA rules. :confused

O.. ok, maybe no tuning then. Just dyno.. but it HAS to be Dynojet as required by NASA rules. :confused
I'd possibly be in for the same reason.

I only have experience with EIP, but here is a list of all/most of the dynojets in MD.
http://www.dynojet.com/maps/autodynos/md.htm

I'm sure this goes without saying, but make sure whoever you do go too knows how to tie down a BMW.

Ive only gone to MainStreet in Damascus. They were cool... and now there is a 5guys upstairs.

But I think they want $75-100 / 3 runs.

Extreme Motorsports in Odenton. Our club is having a dyno day here Sunday actually.
Altered Atmosphere in Gaithersburg.
Mach V Motorsports in Sterling.

Those are all the dynojets Ive used in the area, couldnt tell you if they know how to tie a BMW down though.

Extreme Motorsports in Odenton. Our club is having a dyno day here Sunday actually.
Altered Atmosphere in Gaithersburg.
Mach V Motorsports in Sterling.

Those are all the dynojets Ive used in the area, couldnt tell you if they know how to tie a BMW down though.

do you guys have spots open?

do you guys have spots open?

Nein, all full sorry. When is the VIR event? We're doing another one at Altered in February but I dont know exactly when.

Nein, all full sorry. When is the VIR event? We're doing another one at Altered in February but I dont know exactly when.

2/18-2/19

Extreme Motorsports in Odenton. Our club is having a dyno day here Sunday actually.

Mikey, what time will you all be there? I would like to stop by for a little to check it out.

Mikey, what time will you all be there? I would like to stop by for a little to check it out.

I was thinking of being there around 11 or so. No Hondas allowed, sorry. :(

Ert.......

Extreme Motorsports in Odenton. Our club is having a dyno day here Sunday actually.
Altered Atmosphere in Gaithersburg.
Mach V Motorsports in Sterling.

Those are all the dynojets Ive used in the area, couldnt tell you if they know how to tie a BMW down though.
Considering AA has several boosted RWD or AWD shop cars, I'd say they know how to tie one down. They have an All-Wheel Drive Dynojet... and it looks like they charge accordingly :eek:

http://www.alteredatmosphere.com/tuning.asp

I would be down for a dyno day.....

Ert.......
wanna set up a day in early Feb?

I was thinking of being there around 11 or so. No Hondas allowed, sorry. :(
It was worth the 5 mile walk. Evos are freakin AWESOME! :eek
From the interior to the exterior, and especially the engine!

Turbos are cooooool.

We had our dyno day at FCCT in sterling, right off 28. www.fcct.net is the site, they charged $75 for 3 pulls with a/f mixture....they have some sick shop cars in there too, two DSMs, two vettes, and a 5.0 stang and a 4.6 stang...they also built a 6sec pro street drag car. Pretty nuts.

I think they run a pretty good shop :)

We had our dyno day at FCCT in sterling, right off 28. www.fcct.net is the site, they charged $75 for 3 pulls with a/f mixture....they have some sick shop cars in there too, two DSMs, two vettes, and a 5.0 stang and a 4.6 stang...they also built a 6sec pro street drag car. Pretty nuts.

I think they run a pretty good shop :)

Im scared to have one in VA... people would get pulled over going there fo rhaving an exhaust :rolleyes:

wanna set up a day in early Feb?


Let me talk to my boss Alfred. As of right now we cannot tune a car. The Horeba (however you spell it) is broken. But getting #'s is fine.....



Jason

Let me talk to my boss Alfred. As of right now we cannot tune a car. The Horeba (however you spell it) is broken. But getting #'s is fine.....



Jason

Late Jan or Early Feb is fine by me.

Let me talk to my boss Alfred. As of right now we cannot tune a car. The Horeba (however you spell it) is broken. But getting #'s is fine.....



Jason
Sounds good Jason, I just need numbers anyhow (the lower the better).

Edit: I can do it pretty much any Saturday but this weekend, picking the car up :buttrock

VAC Motorsports in Philly just got a new dyno lot of tuning capabilty chip burning. Im not sure what it is but maybe email them www.vacmotorsports.com he does alot of BMW CLub race stuff

I'm down for a dyno day (on a DynoJet). Altered was good the last time I went.

Let me talk to my boss Alfred. As of right now we cannot tune a car. The Horeba (however you spell it) is broken. But getting #'s is fine.....

Jason

Jason, did you find anymore info on this? If we dont set this up soon, Im going to have to do it on my own....

You just want to dyno or tune? Dyno's are a dime a dozen.. for tuning, try Cyntex up in PA.

You just want to dyno or tune? Dyno's are a dime a dozen.. for tuning, try Cyntex up in PA.

I just need a dyno... on a dynojet to be exact. Need to have this done by 2/17.

There' that DYNApack shop in Springfield and there is a Mustang shop here in Springfield that has a Mustang dyno. The DYNA pack one had a dyno day a few months ago for 50 each but no tuning at that time. They are $75 an hour.