UPDATE!!! Finally ready. I am selling my AA stage 1.5 Gen 2+ kit for OBD1. The kit is complete and works great, but it is time for a custom MONSTER TURBO Kit. There are many upgrades and improvements included from the base kit. Over 300RWHP(360CrankHP)!

Included is:

1. AA stage 1 turbo completely rebuilt w/ ported exhaust port.
2. Internal wastegate removed. External TiAL 40mm wastegate included. This eliminates boost creep problems originally in this kit.
3. MUCH Larger Intercooler! Sized approximately same as TT stage 2 IC.
4. Completely re-designed turbo to IC pipe. Upsized from 2 to 2.5" and routing follows TT stage 2.
5. Euro MA with NickG tuned IC. Great AFRs and day to day driveability.
6. AA Exhaust available for additional cost.
7. Larger Injectors
8. Full Installation manual.
9. Rest of the hoses, connectors, clamps etc

PRICE REDUCED! First offer over $4200 gets it. PM for additional questions.

how much for just exhuast? track pipe too?

$300 for the AA muffler. No track pipe because of custom exhaust for turbo

fzust is an honest seller folks. As far as I know, this kit is as complete as can be for a used setup.

Finally ready to sell. Lower price! See edited message above.

bump for local phx guy

How many miles have you put on the kit? What will be needed that is not included to complete the install?

How many miles have you put on the kit? What will be needed that is not included to complete the install?

About 10k miles since the turbo re-build. This was a complete re-build w/ replacement of all the seals and bearings etc. This was also when the porting of the turbine was done. Everything is included that I can think of, including hoses & hose clamps etc. I used my Electronic Boost controller on my new setup, so if you want one, pick your favorite and buy it. Otherwise you can run off the wastegate spring. I need to pickup some hose of the water coolant lines for the turbo, but I will include that with the kit for the buyer. I will throw in a couple of extra hose clamps just in case. To be honest, I miss the immediacy of this kit. The bigger turbo I have is great, but it feels like a "turbo car". This kit spools very fast and since it uses stock compression, it is very responsive.

M-tastic! Thanks for the AZ bump!

I'm interested in the exhaust. Which generation AA exhaust is it? How many miles? Is that 300 shipped? Could you post pics of email them to me at jlac6485@yahoo.com. TIA!

What DME# do you have on your 95?

What DME# do you have on your 95?

I have no clue. Why is that important? It is OBD1, if that helps....

hes asking for the # that appears on the outside of the ECU box. 413 dme is what most 95 guys have unless it was produced earier, which i believe is a 506 . Danp412: tell him which dme# you have and what your production date was.

here is a link explaining a software install by AA. Hopefully that helps. It shows how to find out which dme# you have scroll towards the bottom.
http://aatuning.com/faq/ecu-instructions.html

hes asking for the # that appears on the outside of the ECU box. 413 dme is what most 95 guys have unless it was produced earier, which i believe is a 506 . Danp412: tell him which dme# you have and what your production date was.

here is a link explaining a software install by AA. Hopefully that helps. It shows how to find out which dme# you have scroll towards the bottom.
http://aatuning.com/faq/ecu-instructions.html

I will check. I have a late 95, so I am guessing that is a 413.....

Yea if you have a late build 95 then its probably a 413 like mine (7/95). From what ive noticed, anything that was made in 1995 is a 413 DME.

So are you not gonna sell this kit for less than $4200?

Yea if you have a late build 95 then its probably a 413 like mine (7/95). From what ive noticed, anything that was made in 1995 is a 413 DME.

So are you not gonna sell this kit for less than $4200?

PM sent

Reply sent :)

hes asking for the # that appears on the outside of the ECU box. 413 dme is what most 95 guys have unless it was produced earier, which i believe is a 506 . Danp412: tell him which dme# you have and what your production date was.

here is a link explaining a software install by AA. Hopefully that helps. It shows how to find out which dme# you have scroll towards the bottom.
http://aatuning.com/faq/ecu-instructions.html

Confirmed it is 413.

fzust i see that you are in az... im a complete noob to installing a turbo but i love in az and if u havnt sold the kit id like to get in contact with you. Please let me know if this turbo has been sold as im looking to bump of the power of my E36 M3 :) BTW do you know anyone who could install this for me! Glad to see your in az so im hoping i can go through on this. Thanks

-Rudy

Hi Rudy. Even better, I am in Tempe/Chandler area. PM sent!

Will you sell the turbo manifold by itself? Let me know.

Shawn

Hey Fred.

If you decide to part out your kit, I am willing to buy a few items from you. I'm the one who bought the exhaust off you if don't remember.

what would be needed for obd2....just ecu tuning?

I don't think I will be interested in parting it out, but PM me and let me know. I hope you enjoy the exhaust!

what would be needed for obd2....just ecu tuning?

Yes, just ECU tuning

sent a pm!

interested in parting with the software portion? if so what DME do you have?506 or 413

This kit is now Sold!