Master Power t3/t70 turbo,

this turbo will fit on all aa manifold, and turbonetic manifolds.


0.70 A/R compressor housing. Super 70 Trim compressor wheel (flows more than 85 lbs/min).

Exhaust is a .84 ar with p trim wheel and thermal coated. Less than 500 miles on it.

Going with a different turbo. $550 + shipping.

exhuast side

Man thats a sweet looken turbo...

BUMP for geat turbo ....

$575.00 + shipping.

What kind of hp numbers would a buyer expect from that turbo?

What kind of hp numbers would a buyer expect from that turbo?


depends on how much boost you want to run. but easily into the 600rwhp +

what did this run new?

it was 700 new + the thermal coating. so it came out to about 800.

bump...buyer backed out. $550 +shipping.

I have a Masterpower turbo.. the shyt spools like a BB turbo nice and quick. Its made Germany and they are very reliable i think they are good up to 700 hp.

I know very little about turbo, but so far I've picked up that the GT35R is a great match for the S50/S52 engine.

Would the T3/T70 be a good match for the M50?

I know very little about turbo, but so far I've picked up that the GT35R is a great match for the S50/S52 engine.

Would the T3/T70 be a good match for the M50?


it is if the motor is built and capable of doing 20psi or higher.

I have a Masterpower turbo.. the shyt spools like a BB turbo nice and quick. Its made Germany and they are very reliable i think they are good up to 700 hp.


They spool fast for the size, they use a lightweight shaft system. For the size it spools good. this particular turbo is good for 800+hp.

They spool fast for the size, they use a lightweight shaft system. For the size it spools good. this particular turbo is good for 800+hp.


yea yours is a tiny bit bigger then my i think.. what is your a 60/58 Q-trim

yea yours is a tiny bit bigger then my i think.. what is your a 60/58 Q-trim


its uses a .84 ar housing with a ptrim wheel.

its uses a .84 ar housing with a ptrim wheel.
.50 ar is my turbo...
what kind of engine work did you have done..

compressor map links?

.50 ar is my turbo...
what kind of engine work did you have done..


forged pistons, rods, 3.2L crank.

compressor map links?


here you go

I am very interested, but have a couple questions you may or may not be able to answer. I am looking to build a 2.8L motor, and looking to push around 400-500 rwhp. Is this turbo too big for my type of application? Also, does this turbo spool nicely over 20 psi? Or could I use it for like 15 psi-18 psi?

As far as manifolds go, would you recommend the turbonetics or AA manifold? You said both would work with this turbo right?

One final question, would the 2.8L handle around 20psi with just a HG, or do you think I would need rods/pistons etc. Thank You for your time.

by the way, what power are you putting down? and could you list your mods/PSI for me as well. Thanks again

I am very interested, but have a couple questions you may or may not be able to answer. I am looking to build a 2.8L motor, and looking to push around 400-500 rwhp. Is this turbo too big for my type of application? Also, does this turbo spool nicely over 20 psi? Or could I use it for like 15 psi-18 psi?

As far as manifolds go, would you recommend the turbonetics or AA manifold? You said both would work with this turbo right?

One final question, would the 2.8L handle around 20psi with just a HG, or do you think I would need rods/pistons etc. Thank You for your time.

by the way, what power are you putting down? and could you list your mods/PSI for me as well. Thanks again


for the size it spools pretty good. you probalby can get away with smaller turbo for 400-500rwhp. but if your looking to make some big power this turbo will do it. for the 400-500 miles i used it, i used it mostly on 14psi. It felt great, pulled really hard.

yes this will fit the aa and turbonetics manifold.

Well a member by the name of card counter is doing 25psi with just a headgasket, but i would do rods and pistons for over 18psi.

i never got to tune the car in all the way in so I didnt get any final number but at 18 psi it was making over 550rwhp.

thank you very much. I will get back to you.

if you need a Mani i could make you a costum one that should fit this puppy nicely..

here you go
hhhhmmm.......


This seems a bit larger then i really need....All im running is the VAC .140
HG and ARP studs, shaved head .004...... I wonder how that would work for me at 18PSI.

What waste gate were you using and when did this puppy make full boost, on the 3.0 motor? (is that what you were using?)

Feel free to PM or E-Mail me.... VERY interested

bump

500 + shipping

$475+ shipping, any takers?

$475+ shipping, any takers?
I am looking into it now. At what rpm will it hit 15+psi?

I am looking into it now. At what rpm will it hit 15+psi?


Not too sure, i didnt even get to drive on this turbo long. i think low high 3ks or low 4ks.

bump

any takers for $425??

nevermind, saw earlier post...

How would this be on a M50 non vanos motor? It would be built w/ low comp pistons, forged rods etc. Let me know as the price is awesome. Thanks


not too sure, should pretty good with a built motor and high boost :buttrock

bump

I would love to pick this up, but I am still reading up on turbos. I am also looking to run low boost around 10-12psi so I will not have to do a HG. I knew thats close, but I think I might give it a shot. Will this turbo really do anything for me at 10-12?

what was the max out put of your car when you was runing high boost.. is this turbo good for 700 hp?

I would love to pick this up, but I am still reading up on turbos. I am also looking to run low boost around 10-12psi so I will not have to do a HG. I knew thats close, but I think I might give it a shot. Will this turbo really do anything for me at 10-12?


10-12psi will work, but the turbo really comes alive in high boost

what was the max out put of your car when you was runing high boost.. is this turbo good for 700 hp?


I am not sure, never got to get a tune in with high boost, the turbo is good for ~800 + crank hp.

How much is shipping on this bad boy?

How much is shipping on this bad boy?


probably about $18

$400 shipped.

bump

Could you please post the part# for this turbo? Should be an 8 digit# on a tag on the center section. Thank You.

Could you please post the part# for this turbo? Should be an 8 digit# on a tag on the center section. Thank You.


the numbers i have on the tag are

810015

04j179146

St2

Email sent. Free bump :)

bump

375 + shipping, i need to sell this.

i will buy it!! send me a email.. nadderley74@hotmail.com

I'm ready to buy today..

Thanks Neal

P.S. sorry i just looked at the post date..