Battery change info

[oneeyefrail]

OK so I've just had to change the battery in my E60 530, went into DIS and registered the battery change but it says i also need to go somewhere else to change the battery amps,old one 110 new one 100( i think it said CAS ) but cant find anything ? is it enough just to register the battery change ? cheers

[rondo]

Hi look in C:\NCSEXPER\DATEN and rename the E60AT.000 as a .TXT file and then open and find some good info in this file..

[oneeyefrail]

thanks but sorry for the delay in reply ,changed it but that text that came up means NOTHING to me :(

[Gene Poole]

You didn't find this:



//************************************************** ****************************
//ACHTUNG: Wegen Ueberschneidung mit KMM sind keine E- und K-Worte zugelassen, die mit "L" oder "P" beginnen
//E: aktive Ergaenzungszeilen (PUSY-Relevanz fuer Steuerung SA<100) nur WERK!
E EWS4 //EWS4 //Vorhalt fuer neue EWS Generation (nicht codierrelevant!)
E NMUW NEUE_MUW //Einsatz neuer MUW Sensoren bei allen E63 und E64 (Akt. Innenraumschutz bei CANSINE CI03 && CI04)
E B080 BATTERIE_80AH //80 Ah-Batterie
E B090 BATTERIE_90AH //90 Ah-Batterie
E B110 BATTERIE_110AH //110 Ah-Batterie
E A090 BATT_AGM_90AH //90 Ah-AGM Batterie (SA536)
E A080 BATT_AGM_80AH //80 Ah-AGM Batterie
E ASIA //MASK-Asien-Muster frei neben der SA China & Korea
E 701S SECURITY //Sondercodierung Sicherheitsfahrzeug Mexiko
E 702S SECUR_SODER_W //Sondercodierung FH_HINTEN Sicherheitsfahrzeug Mexiko
E 703S SECUR_A_KID //Sondercodierung Schlüsselabziehen in jeder Getriebeschalterstellung

[oneeyefrail]

yea found found that but dont know what to do with it .. anyhelp please
putting a 100 amp battery in,was 110

[Gene Poole]

Well, it looks like your only options are 90 and 110. You could remove B110 from your VO and add B090, but your still 10 amps off. I don't know whether you should go high or low.

[oneeyefrail]

sorry but im a complete newbie with this :( how and where to i go about this ? can i do this in INPA or DIs ? any others got advice on this ?
I fitted a Bosch battery a couple of weeks ago s and its killed the battery :( so got another one,(the 100 amp was recommended for the car from Halfords)
Not sure if its overcharging it or what :( thanks

[Gene Poole]

I found this in another forum:
http://www.bimmerfest.com/forums/showpost.php?p=4945381&postcount=7


Thanks to Keif and the folks on here for helping me with this.

Just to feedback.....

If you have INPA working, then select the following to Register the new battery

1. Select BODY from the left hand pop-up menu
2. Select POWER MODULE in the right hand list
3. Select ACTIVATE from the next menu
4. Another menu comes up, which has ACTIVATE1 and ACTIVATE2.
5. Select ACTIVATE2 from the menu
6. Then select F7 - Register battery replacement

Almost instantly you get the message:
"Register battery replacement Activated properly."

Job done!

Hope this helps!

[oneeyefrail]

cheers but that doesnt seem to be relevent to my version unless im being stoopid:( im running inpa loader version 5

[oneeyefrail]

attached screen print

[rondo]

Hi do you have an AGM style battery or regular ?Have you checked with voltmeter to see what alternator is doing?

[oneeyefrail]

yea putting out 14,4 volts :( need to find out why its killed this new battery:( could the IBS have anything to do with the battery getting killed ?not getting any error codes from the ibs though

[oneeyefrail]

BUMP ....

anyone ?... Waiting on a new IBS to try this... do i need to recode this?

[Tavher]

I have replaced my 90Ah AGM battery with new BOSCH S5 110Ah and tried to register it:
- in NCS Expert I changed the value KLASSE_BATTERIE in CAS module to 110Ah (if I read the module again the new value is set and correct)
- in Toolset 32 I opened MSD80 and executed jub steuern_batterietausch_registri and the status was OK (I also tried with MSV70 and MSV80)

But when I check the PM Field 2 in INPA there is still 91Ah as it was before. I also tried B TAUSCH in INPA and also repeated the process.

I dont know why it is 91Ah when it was 90Ah battery installed, but shouldnt I see 110Ah now?

I have E61 2006. Is the procedure different? Or where could be the problem?

Thank you for your suggestions!

[rondo]

Hi found this on another forum maybe it will help
Battery (IBS) reset can be done with INPA.

1 Select your car model
2 Select your engine type (select the one with MS or MSV in front of the engine type)
3 Select Status (F5)
4 Select PM-IBS (F5)
5 Click B Exchange (F5)
6 Popup (OK) should appear if job is done.